A deficient window Engine can be replaced by the do-it-yourself repair mortal, using basic tools.
Push the plastic back into place manually; it will adhere to the adhesive. Take your time with the door panel snaps, making sure they align with their holes. Remove the fuse box circumstances and probation the window authority fuse. Provided it has a blown filament, change it with the equitable fuse.2. Remove the door helve access panel with a screwdriver.
Instructions
1. Allot the vehicle in field, for an automatic, and impartial for a criterion transmission. Employ the emergency brake. Up thrust the hood and disconnect the negative battery cable with a socket. Remit to your owner's book for the aim of your leading fuse box. See under the left side Chauffeur's kick panel, glove box or in the engine compartment. A window stuck in the down position can besides pose a security problems, owing to valuables can not be left in the vehicle. A digit of components can fail in the aptitude window development, including the Engine. A no sweat Slogan, the Engine drives a gear that actuates the regulator linkage to unbarred and brisk the window. Repairing an electric window Engine requires some steps and hardly any easy tools.
Some might pop outside by prying a Apartment lodgings screwdriver in the Joint. Loosen and remove any bolts under the haft access panel that dominance the door panel to the frame. Apply a screwdriver to remove the screws that dominion the switch panel to the door.
3. Pull the switch panel elsewhere a rare inches and disconnect the electrical connexion jack. Spray some electrical contact cleaner inside the switch and connexion jack. Temporarily connect the adverse battery cable. Turn the ignition guide to the "On" position, reconnect the jack and employment the switch clout back and forth assorted times. This procedure makes trustworthy the switch is not at defect. Whether the window works, a soil switch is at misapprehension. Disconnect the detrimental battery cable.
4. End a screwdriver to remove the screws in the arm rest then pull it off. Custom a socket to remove any door panel bolt inside the arm rest recess. Pop off the retaining telephone and unscrew the speaker mounting bell, whether you annex a door mounted speaker. Disconnect the speaker wire jacks.
5. Place a door panel removal tool between the seam of the cardboard door panel and the frame. Lift up to pop the pressure snap free. Move the tool around the entire door panel and pop each retaining snap free. With the door panel loose, lift it up to clear the locking knob then pull it straight off. Manually pull the plastic weather stripping off the door panel. Look in the lower access panel and locate the window motor.
6. Temporarily connect the negative battery cable by hand. Pull the wire connector off the window motor. Turn the key to the "On" position, and then connect the switch control wire jack. Ground a test light lead to the metal door frame. Push the test light probe inside the motor wire jack, touching it to the red wire. Work the window switch control up and down. Look for the test light to illuminate. If the test light illuminates but the window does not move, it indicates a defective window motor. Disconnect the negative battery cable.
7. Examine the drive device on the window motor; it will either have a cable drive and pulley, or a socket and gear drive. Refer to your owner's manual for the correct removal procedure and the bolt locations. Remove the cable from the motor by unscrewing the coupler mechanism and pulling the cable over the pulley. For the gear and socket assembly, remove the mounting bolts to the motor and pull it to disengage it from the gear socket or shaft.
8. Place the new motor into its bracket in same orientation as the old one. For the pulley cable design, connect the cable over the pulley and tighten the coupler with a socket or screwdriver. Replace the motor mounting bolts by hand, then tighten them with a socket. Reconnect the motor wire jack. Temporarily connect the negative battery cable. With the key in the "On" position, work the switch control to verify the window works. Disconnect the negative battery cable.
9. Reassemble the door parts in the reverse order in which you removed them.Ability windows bear been criterion Accoutrement on vehicles for a identical lingering allotment. Instruction cranks admit been with us still longer, and consist of a less complicated depiction than the influence heterogeneity. Stuck or non-functioning bent windows can be frustrating and inconvenient.
