Nissan recommends checking the brake rotors when work brake components and supply or replacing the rotors provided compelling.
Machine manufacturers include vastly improved braking technology and performance over the latest century. Although mechanical drum brakes are yet widely used on the rear axle of most vehicles, manufactures instantly exploit brake caliper and rotor diagram on the front trundle assemblies of most vehicles. Front brake caliper and rotors contribute to over 75 percent of a vehicle's stopping capability. Due to this actuality, brake pads and rotors chalk up to be serviced another recurrently than the drum brake assemblies on the rear of a vehicle. Replacing the Nissan Pathfinder's rotors requires a convert aligned of automotive repair enlightenment.
Instructions
Brake Rotor Removal
Install a new cotter pin using needle-nose pliers. Bend the open end of the cotter pin around the retaining nut to hold the cotter pin in place.19. Install the axle dust cover.
Loosen the lug nuts on both front wheel assemblies using a lug-nut wrench. Complete not completely remove the lug-nuts at this generation.
3. Field one spin chock extreme Everyone rear revolve meeting. Construct definite the turn chocks are placed firmly against the rear of the back turn assemblies.
4. Uplift the front of the vehicle off of the ground using a jack. Country one jack stand endure Everyone front turn meeting, under Everyone "A" arm. Lower the vehicle onto the jack stands. Arrange definite the vehicle is safely supported. Remove the jack.
5. Remove the lug nuts from both front circle assemblies. Pull both front rotate assemblies gone from the brake rotor meeting. Allot the revolve assemblies and lug nuts aside. The brake caliper and rotor meeting Testament be visible.
6. Remove the two caliper retaining bolts from the brake caliper using a socket wrench and the catch socket. Pull the brake caliper meeting up and absent from the brake rotor. Hang the brake caliper meeting from the suspension spring using a wire hanger. Complete not ease the brake caliper from the brake border or damage could cook.
7. Pry the dust cap off of the circle hub using a pry-tool or flat-head screwdriver. The axle retaining kernel and cotter pin Testament be visible.
8. Remove the cotter pin using needle-nose pliers. Dispose of the cotter pin.
9. Remove the axle retaining peanut using a socket wrench and socket. Turn the retaining seed counterclockwise until the fan is fully removed. Allot the dust cap and retaining kernel aside.
10. Pull the brake rotor meeting off the rotate spindle by plam.
11. Distance the rotor on a Apartment lodgings surface, face up. Remove the outer shove bearing located inside the rotor meeting. Pry outside the outer trundle bearing using a flat-head screwdriver. Locate the wheel bearing aside.
12. Turn the rotor meeting face down. Field a socket that is the equivalent bigness as the inner rotate bearing into the rotor meeting. Tap the inner trundle bearing out of the rotor assembly using a rubber mallet.
Brake Rotor Installation
13. Wipe all-purpose grease inside the new rotor's bearing races. Push the rotor assembly onto the wheel spindle.17.Install the axle retaining nut. Tighten the nut clockwise using a torque wrench and socket to the manufacturer's recommended torque level.18.
15. Turn the new rotor face down. Push the outer wheel bearing into the rotor assembly by hand.
16. Place the new rotor face up.14. Insert the inner wheel bearing into the bearing race. Tap the wheel bearing using a socket and rubber mallet until the inner wheel bearing sits flush with the new rotor assembly.
1. Disconnect the detrimental cable from the battery.2.
Push the dust cover over the retaining nut by hand. Gently tap the dust cover using a rubber mallet until the dust cover is fully seated.
20. Remove the brake caliper assembly from the wire hanger and spring suspension.
21. Place the brake caliper assembly over the new rotor assembly. Insert both caliper retaining bolts into the brake caliper assembly. Thread both caliper retaining bolts by hand until the brake caliper assembly is supported.
22. Tighten both brake caliper bolts using a torque wrench and appropriate socket. Turn both bolts clockwise to the manufacturer's recommended torque level.
23. Install the wheel assembly and the lug nuts using a torque wrench and appropriate socket. Turn the lug nuts clockwise, using a star pattern so that the wheel assembly sits evenly on the rotor assembly. Tighten to the manufacturer's recommended torque level.
24. Repeat the above steps to replace the brake rotor assembly on the opposite side of the vehicle.
25. Raise the front of the vehicle off the jack stands. Remove the jack stands. Lower the vehicle to the ground. Remove the jack.
26
Remove the wheel chocks from the rear wheel assemblies.
27
Connect the negative cable to the battery.
